机械词汇很全.docx
- 文档编号:15609349
- 上传时间:2023-07-06
- 格式:DOCX
- 页数:44
- 大小:49.79KB
机械词汇很全.docx
《机械词汇很全.docx》由会员分享,可在线阅读,更多相关《机械词汇很全.docx(44页珍藏版)》请在冰点文库上搜索。
机械词汇很全
机械词汇很全
flange connection.凸缘联接 stockpile贮存
Goggles:
护目镜 packing list装箱单
crate:
柳条箱 purchased material list原材料进货单
back-feed反馈 wire coil线盘, 线卷,
NPT thread. 美国标准锥管螺纹 cable gland 电缆衬垫
terminal block线弧, 接头排 接线盒, 接线板, 线夹
power drill机械钻 connector. 接线器
insulated sleeve绝缘套管 wire connector接线器
wire terminal电线接头 control wiring操纵线路
motor lead电动机引出线 power wiring电力布线
tender document.提供证件 orifice plate.挡板 nut 螺母
flange gasket 法兰垫片 dimensional inspection 尺寸检验
burn through 烧蚀 piping system.管道系统
reinforcement of weld加强焊缝 fabrication.制造
dye penetrant examination染料渗透试验法
magnetic particle examination 磁粉检验 butt weld 对接焊缝
girth weld环形焊缝 cement lined piping 水泥衬里
weld joint 焊缝, 焊接接头 spool drawing 管路图, 管路详图
spot test 抽查, 当场测试 assembly.装配
Random Radiography随机射线照相检查
radiographic examination 射线照相检查 examination试验
erection 架设 arc welding 电弧焊
cable tray.电缆盘 rigid steel conduit 钢制电线管
power control 功率操纵 normal bend 法向[法线]弯管
control cable操纵电缆 操纵索 grounding conductor 接地导体
cable glands:
电缆衬垫 exfoliation剥落
power receptacle 电力插座 junction box 分线箱
lighting fixture照明器材 Circuit breaker断路开关
race way 电缆管道 terminal box接线盒
distribution board配电盘, 配电屏 receptacle 插座
tumble switch.翻转开关,拨动式开关 amplifier panel 放大器盘
cathodic protection system 阴极爱护系统 control console 操纵台
electrical material电气材料 convenience receptacle.电源插座
cable gland 电缆衬垫 filler rod焊条shield gas 爱护气体
TIG:
Tungsten-arc Inert-Gas welding 钨极电弧惰性气体爱护焊
tensile strength 抗张强度 shield jig爱护夹具
high frequency generator.高频发电机 welding rod 焊条
filler metal 焊料, 焊丝 shop fabrication 车间制造
field installation 现场安装 welding bead 焊道
both sides welding.双面焊接 residual stress 残余应力
electrode 电焊条 condensation 冷凝 longitudinal.纵向的
horizontal line 水平线 circumferential joint 周圈接缝
nondestructive examination.非破坏性检验, qualification:
合格性
construction work施工工程 welded joint焊接缝 焊接节点
gas cutting.气割 arc cutting电弧切割 grind off 磨掉
metallic luster 金属光泽 Screwed Piping Joints螺丝状的管接头
gouging .刨削槽 Bending:
挠曲 witness test订货人在场的试验
Welding:
焊接 Threading:
车缧纹 Leveling:
校平
color identification 彩色识别 Alignment:
对准,定位调整
check against 检查, 核对 Fixing:
固定 Console:
操纵台
cubicle室,箱 audit 审计 material certificate.材料合格证
vertical panel竖直面板 power distribution panel 配电盘
gauge board外表板 beveling 磨斜棱,磨斜边 local panel 现场配电盘
grouting 灌浆 fabrication 加工,制造 instrument rack 计测器支架
tank gauge 液面计 flushing 冲洗,填缝 analyzer分析器
piping管道敷设 tubing敷设管道 cable fitting电缆配件
elbow.弯管接头 main pipe 主管道 bend.弯管弯头
solvent 溶剂 postweld heat treatment 焊后热处理 jig.夹具
arc gouging 电弧刨削 chipping修琢 machining 机械加工
bridges.管式桥 clamp.夹钳 tack welding 点焊
butt welding 对接焊 grinder. 磨床 commencement.开始
gusset plate角撑板, 加固板 process pipe 工艺管道 land 纹间表面
tee 三通管 丁字钢 T形梁 opening 开口 reinforcing pad.补强垫,增强衬板
flux 焊剂 wet developer 湿显像剂 blowhole气泡,气孔
inclusion 杂质 imperfection 缺陷 limitation 限度 valve 阀,闸门
structural attachment 结构附件 tapered allowance 削尖余量
tack welding 平头焊接 sputter 喷溅 scale 废料
lateral translation侧向平移 weld joint 焊缝, 焊接接头 plug.塞
fusion 熔融 base material基底材料 lead foil 铅箔
intensifying screen 增光屏, 光增强屏 pressure test.压力试验
film density.影片密度 line number行数 leak test漏泄试验
plate thickness 筛板厚度 restoration修理
field fabricated 工地制造的,现场装配的 junction box.接线盒
flow sheet 流程图 vent 放气孔, 通风孔 drain 排水管
机械专业英语词汇〔专门全〕
金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals
刀具 cutter 摩擦 friction 联结 link传动 drive/transmission
轴 shaft 弹性 elasticity 频率特性 frequency characteristic
误差 error 响应 response定位 allocation机床夹具 jig
动力学 dynamic 运动学 kinematic静力学 static拉伸 pulling
分析力学 analyse mechanics压缩 hitting 剪切 shear
扭转 twist弯曲应力 bending stress 强度 intensity
三相交流电 three-phase AC 磁路 magnetic circles
变压器 transformer 异步电动机 asynchronous motor 几何形状 geometrical
精度 precision正弦形的 sinusoid 交流电路 AC circuit
机械加工余量 machining allowance变形力 deforming force退火 anneal
变形 deformation应力 stress硬度 rigidity 热处理 heat treatment
正火 normalizing脱碳 decarburization渗碳 carburization 电路 circuit
半导体元件 semiconductor element反馈 feedback 发生器 generator
直流电源 DC electrical source 门电路 gate circuit 逻辑代数 logic algebra
外圆磨削 external grinding 内圆磨削 internal grinding 绞孔 fraising
平面磨削 plane grinding变速箱 gearbox 离合器 clutch
绞刀 reamer螺纹加工 thread processing螺钉 screw 铣削 mill
铣刀 milling cutter 功率 power工件 workpiece齿轮加工 gear mechining
齿轮 gear主运动 main movement主运动方向 direction of main movement
进给方向 direction of feed 进给运动 feed movement
合成进给运动 resultant movement of feed前刀面 rake face
合成切削运动 resultant movement of cutting刀尖 nose of tool
合成切削运动方向 direction of resultant movement of cutting前角 rake angle
切削深度 cutting depth
机械专业词汇:
hardenability 淬透性carbide tool 硬质合金刀具alloy tool steel 合金工具钢
alloyed cast iron 合金铸铁carbon steel 碳素钢carbon tool steel 碳素工具钢
cast iron 铸铁cast steel 铸钢die material 模具材料
high alloy steel 高合金钢high carbon steel 高碳钢low alloy steel 低合金钢
low carbon steel 低碳钢shock resistant tool steel 抗冲击工具钢
nodular graphite iron 球墨铸铁malleable cast iron 可锻铸铁
mottled cast iron 麻口铸铁hardenability curve 淬透性曲线
hardening capacity 淬硬性〔硬化能力〕hardness penetration diagram 〝U〞形曲线
hardness profile 硬度分布〔硬度梯度〕heat treatment procedure 热处理规范
heat treatment installation 热处理设备heat treatment furnace 热处理炉
heat treatment cycle 热处理工艺周期heat time 加热时刻
heat system 加热系统heating up time 升温时刻heating curve 加热曲线
high temperature carburizing 高温渗碳high temperature tempering 高温回火
isothermal annealing 等温退火interrupted ageing treatment 分级时效处理
local heat treatment 局部热处理overheated structure 过热组织
pack carburizing 固体渗碳Oxynitrocarburizing 氧氮碳共渗
partial annealing 不完全退火recrystallization temperature 再结晶温度
cutting part 切削部分tool angle 刀具角度tool back angle 背前角
tool back clearance 背后角tool backlash movement (tool retracting) 退刀
tool back wedge angle 背楔角tool base clearance 基后角
tool cutting edge plane 切削平面tool cutting edge angle 主偏角
tool grinding machine 工具磨床tool geometrical rake 几何前角
tool nomal clearance(rake) 法后角〔法前角〕locating device 定位装置
tool orthogonal clearance(rake, wedge) 后角〔前角,楔角〕
locating face 定位面locating pin 定位销〔挡料销〕locating plate 定位板
locating ring 定位圈locating rule 定位尺locating element 定位零件〔定位要素〕
work hardening 加工硬化internal cylindrical grinding machine 内圆磨床
internal cylindrical turing 内圆车削internal force 内力
internal cylindrical grinding machine with vertica 立式内圆磨床
hole scraping (turning,milling, lapping) 刮孔〔车孔,铣孔,研孔〕
hole grinding (slotting,honing, flanging) 磨孔〔插孔,珩孔,翻孔〕
versatile grinding machine 多用磨床versatile lathe 多用车床
vertical multi-tool lathe 立式多刀车床precision milling machine 周密铣床
spot face 孔口平面drill and countersink 定心钻,中心钻
counterbore cutter head 扩孔钻头jig boring machine 坐标镗床
jig grinding machine 坐标磨床jig and fixture 夹具
fixture of gear cutting machine 齿轮加工机床夹具
fixture of milling machine 铣床夹具fixture of grinding machine 磨床夹具
fixture of planing machine 刨床夹具fixture of slotting machine 插床夹具
vacuum fixture 真空夹具universal fixture (jig) 通用夹具stationary fixture 固定夹具standard fixture (jig) 标准夹具
pneumatic fixture (jig) 气动夹具open-side boring and milling machine 悬臂镗铣床
magnetic fixture (jig) 磁力夹具locating device (face,element) 定位装置〔面,元素〕
hydraulic fixture (jig) 液压夹具slide gauge 游标卡尺triple action press 三动压力机
tow point single action press 双点单动压力机watch press 台式压力机
closed type single action crank press 闭式单动〔曲柄〕压力机
one point single action press 单点单动压力机
open-back inclinable press 开式双柱可倾压力机
four crank press 四曲柄压力机
stright side single action double crank press 闭式双点单动双曲柄压力机
single piece frame press 整体框架式压力机
rocker arm type press 摇臂式压力机
top drive sheet metal stamping automatic press 上传动板料冲压自动压力机
barrel surface 圆柱形表面antiflowback valve 反流阀
reciprocating-screw machine 往复螺旋注塑机single-stage plunger 单级柱塞
shot chamber 注射室curing temperature 固化温度shot capacity 注射能力
plunger diameter 柱塞直径sectional area of plunger 柱塞面积
hydraulic cylinder 液压缸blanking die 冲裁模
blanking clearance, die clearance 冲裁间隙blanking force 冲裁力
die,stamping and punching die 冲模tonnage of press 压力机吨位
shut height of press machine 压力机闭合高度center of die, center of load 压力中心
clearance between punch and die 凹凸模间隙tolerance of fit 配合公差
shearing force diagram 剪力图peak die load 模具最大负荷
clamping force (element, device, piston) 夹紧力〔件,装置,活塞〕
clamp plate (ring) 压板〔夹紧环〕shearing force (plane) 剪切力〔平面〕
side clearance angle 侧隙角side locating face 侧定位面
side-push plate 侧压板shuttle table 移动工作台matrix plate 凹模固定板
material removal rate 材料切除率sheet matal 板料blanking die 冲裁模
assembling die 复合冲模,装配用模具compound blank and pierce dies 落料冲孔模
shaving die 切边模,修边模shankless die 无柄模具
scrapless progressive die 无废料连续模return-blank type blanking die 顶出式落料模
expanding die 胀形模,扩管模die for special purpose 专用模
cavity plate (block) 凹模bend ability 可弯性bend arc 弯曲弧
bending angle (line) 弯曲角〔线〕bending brake (bending machine) 弯板机,拆弯机
bending fatigue 弯曲疲劳bending radius 弯曲半径
minimum bending radius 最小弯曲半径bending operation 弯曲工序
air-bend die 自由弯曲模bending moment diagram 弯矩图
blank length of bend 弯曲件展开长度
relative bending radius 相对弯曲半径bending equipment for plastics 塑料折弯设备
drawing machine 拉拔机drawing numbers 拉伸次数
drawing ratio (coefficient,force,speed) 拉伸比〔系数,力,速度〕
foamed (cellular) plastic 泡沫塑料Thermoplastic 热塑性塑料
plastic industry 塑料〔工业〕行业blow molding die for plastics 塑料吹模机
standard die components
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 机械 词汇