BLD型锅炉承压管泄漏在线监测系统运行维护安装维护中英文Word文档格式.docx
- 文档编号:7808926
- 上传时间:2023-05-09
- 格式:DOCX
- 页数:83
- 大小:868.98KB
BLD型锅炉承压管泄漏在线监测系统运行维护安装维护中英文Word文档格式.docx
《BLD型锅炉承压管泄漏在线监测系统运行维护安装维护中英文Word文档格式.docx》由会员分享,可在线阅读,更多相关《BLD型锅炉承压管泄漏在线监测系统运行维护安装维护中英文Word文档格式.docx(83页珍藏版)》请在冰点文库上搜索。
锅炉承压管泄漏在线监测系统,是一套专门为及时发现锅炉“四管”泄漏(内漏)事故而设计的“计算机在线监测系统”,该系统主要分为就地检测部分和操作监测部分。
BLDTypeOn-lineLeakageMonitoringSystemforPressurizedTubesinBoiler,isa“on-linemonitoringcomputer”whichisdesignedspecificallyfordetectingleakage(leakageinside)of“4Tubes”ofboilerintime.Thesystemincludes:
groundedmonitoringpartandoperationmonitoringpart.
系统的就地检测部分安装在锅炉现场,操作监测部分则集成在监测机柜中,安装在单元控制室或电子设备间内。
Groundedmonitoringpartisinstalledatboileronsite;
operationmonitoringpartisintegratedinmonitoringcabinet,installedinunitcontrolroomorelectronic-equipmentroom.
1.1安装结构InstallationStructure
整个系统的就地检测部分包括测点声导管、一体化传感器、就地接线盒、就地信号电缆以及防腐清灰装置等。
操作监测部分则包括工控计算机、彩色监视器、监测系统主机、彩色打印机以及系统监测机柜等。
Groundedmonitoringpartincludes:
soundmeatusofobservationpoints,integratedtransducer,groundedjunctionbox,groundedsignalcableandanticorrosivecleaningdevice,etc.Operationmonitoringpartincludes:
colormonitor,monitoringsystemhost,colorprinterandmonitoringcabinetetc.
系统安装结构如图1.1所示。
Installationstructureseefigure1.1:
图1.1 锅炉泄漏监测系统安装结构框图
Figure1.1 Monitoringsysteminstallationstructure
锅炉承压管泄漏在线监测系统的全套设备为贵重仪器,在安装搬运过程中,应尽量注意避免冲击和振动,以免系统设备产生损坏,造成不应有的损失。
Thewholeequipmentsofthemonitoringsystemareveryexpensive.Duringtransportandinstallation,concussionandshakeshouldbeavoided,soasnottodamagedandavoidunnecessarylosses
整套设备应使用一组单独额定热工供电电源,电压240V1A,50HZ,该电源应引入监测机柜中的端子排上。
Thewholeequipmentusesasingleratedthermalpowersupply;
thespecificationis240Vand1A.50HZ.Thepowershouldbeplacedonterminalstripinmonitoringcabinet.
1.2测点安装InstallationofObservationpoints
锅炉承压管泄漏在线监测系统的测点安装,可分为声导管和传感器两部分,其中关键在于声导管的安装。
Installationofobservationpointsofthemonitoringsystemincludes:
soundmeatusandtransducerpart.Thekeypointrestswithinstallationofsoundmeatuspart.
声导管结构StructureofSoundMeatus
声导管用于从炉内传递噪声信号至传感器。
通常由Ø
60×
3.5mm钢管制成,分为J型声导管和Y型声导管,其结构见图1.2和图1.3。
SoundMeatusisusedfortransmittingnoisesignalfromfurnacetotransducer.UsuallyitismadeofsteeltubewhichisØ
3.5mm.ItincludesJ-SoundmeatusandY-Soundmeatus,seefigure1.2andfigure1.3.
(1)J型声导管结构StructureofJ-Soundmeatus
J型声导管主要用于非水平烟道的测点,其结构见图1.2。
图中白钢套的作用是向上移动露出开孔,通过此孔清理声导管内前端的积灰或结焦,还可以适当作看火孔用,此孔平常处于关闭状态。
J-soundmeatusisusedforobservationpointsofnon-levelflues;
itsstructureisshowninfigure1.2.Steeltubeistheroleofexposingholewhilemovingup.Thesoundmeatuscanbecleanedthroughthishole.Italsocouldbeseenasfireholewhennecessary;
itisusuallyclosed.
图1.2J型声导管结构
Figure1.2J-Soundmeatus
(2)Y型声导管结构StructureofY-Soundmeatus
锅炉为平衡通风系统,水平烟道区域易发生正压,正压使烟气进入声导管后在低温结露化合成硫酸,使传感器很快腐蚀,同时声导管前端易积灰。
Boilerisabalancedventilationsystem.Levelflueiseasytoproducepluspressure,andthepluspressuremakesfluegasentersoundmeatus;
thefluegasbecomessulfuricacidatlowtemperature,andmakestranduceretchedquickly,atthesametime,itiseasytopileupashinthefrontofsoundmeatus.
为避免腐蚀和积灰,在水平烟道区域采用图1.3Y型结构声导管。
这种结构声导管有一个气源入口,通过它不断的送入来自锅炉送风机出口的风,用来抵消来自炉膛内部的正压,从而起到防止传感器结露造成的腐蚀,以及防止声导管前端堵灰的作用。
Inordertoavoidbeingerodedorpilingupash,Y-Soundmeatusisusedatthelevelfluepart,seefigure1.3.Y-soundmeatushasanentranceforairsource;
airfromtheoutletofforceddraughtfan,issentthoughconstantlywhichisusedtocounteractpluspressurefromfurnace.Inthisway,thetransducercanbepreventedfrombeingcorrodedandpilingupash.
图1.3Y型声导管结构
Figure1.3Y-Soundmeatus
测点安装位置InstalledLocationofobservationpoints
声导管安装位置由传感器有效监测半径确定,原则为6~12m。
布置传感器的数量应保证对全炉承压受热面泄漏进行有效的监测,且监测应做到无盲区。
Thelocationofsoundmeatusisdecidedbytheeffectiveradiusoftransducermonitoring,usuallyitis6~12m.Thenumberoftransducershouldensurethatallheatingsurfacesleakagecanbedetected,andensurethatthere’snoblindspace.
由于锅炉型号的不同、结构的不同、安装工艺的不同以及锅炉安装地域的不同,因此,测点位置和数量也不同,具体位置应根据锅炉的具体情况而设计,参见测点位置图(附图1)。
Becauseofdifferentboilertypes,structures,installationtechniquesandlocationsoftheboilers,thenumberandlocationofobservationpointsshouldalsobedifferent.Specificlocationshouldbedesignedaccordingtodetailsofboiler,seeattachedfigure1.
Steelgirder
图1.4 侧墙与顶棚声导管安装示意图
Figure1.4 Theinstalledlocationofsoundmeatusonsidewallsandtop-roof
测点布置应遵循以下原则:
Principlesofinstallinglocationofobservationpointsshouldobservetheseprinciples:
(1)传感器有效监测半径为6~12m,避免监测出现盲区。
(1)Inordertoavoidblindspace,theeffectiveradiusoftransduceris6~12m.
(2)安装角度除了顶棚外其它J型声导管为仰角45O,见图1.4;
Y型声导管为仰角30O。
测点上部要留有足够空间。
(2)InstalledangleofJ-soundmeatusisanelevationof45°
excepttop-room,seefigure1.4.InstalledangleofY-soundmeatusisanelevationof30°
.Enoughspaceshouldbekeptatupsideofobservationpoint.
(3)测点位置要有走台,以便于维护。
(3)Platformshouldbelocatedneartheobservationpointformaintenance.
(4)测点确定应避开吹灰器和有压缩风吹扫的其它测点。
(4)Observationpointshouldbekeptawayfromsootblowerandotherobservationpointswhichareblownbycompressionair.
(5)水冷壁区域的测点应尽量利用看火孔、人孔门或闲置不用的其它测点。
(5)Theobservationpointsnearthewater-cooledwallshouldmakeuseoffireholes,manholesorotherunusedobservationpoints.
测点开孔方法TheMethodofBoringHole
(1)水冷壁利用看火孔上方三角区开孔方法
(1)Boringholeonwater-cooledwallmakinguseoftriangleareaabovethefirehole.
大容量锅炉通常为膜式水冷壁,水冷壁间距较小,应尽量利用原有备用吹灰孔、看火孔、人孔门等上方的三角区,减少工作量,避免弯管开孔而破坏水冷壁的原结构。
Thelargecapacityboilerusuallyismembranetubewall;
spacebetweenwater-cooledwallsistoosmall,sothetriangleareabovethesootblowinghole,fireholeandmanholeshouldbeusedasmuchaspossibleinordertoreducetheworkload;
boringholeonsyphonshouldbeavoidinordertoprotectthestructureofwater-cooledwall.
应该注意:
正在应用的吹灰器孔不能利用。
Note:
Thesootblowerholewhichisinusecannotbeutilized.
图1.5 水冷壁利用看火孔上方三角区开孔示意图
Figure1.5 Themethodofboringholewhichmakesuseoffireholeonwater-cooledwall
水冷壁上的原有开孔均有较大的裕度,完全可以利用原开孔上方的空闲三角区安装声导管,见图1.5。
There’susuallyenoughsurplusonoriginalholesonwater-cooledwall,sothetriangleareaabovetheoriginalholescanbeusedforinstallingsoundmeatus,seefigure1.5.
(2)水冷壁弯管开孔方法
(2)Themethodofboringholeonthesyphonofwater-cooledwall
当水冷壁必须弯管开孔时,其具体开孔方法可参见图1.6图。
Whenboringholeonwater-cooledwallisnecessaryonsyphon,themethodseefigure1.6.
图1.6 水冷壁弯管开孔示意图
Figure1.6Themethodofboringholemakinguseofsyphononwater-cooledwall
(3)水冷壁鳍片开孔方法
(3)Themethodofboringholemakinguseoffinnedholeofwater-cooledwall
如果水冷壁测点没有相应的看火孔等可利用,通常锅炉水冷壁管间距较小,考虑到安全因素,则采用在水冷壁鳍片上开窄孔的方式。
竖向结构水冷壁在相邻的鳍片上开两条长的矩形孔,宽度按鳍片实际尺寸。
利用方箱过渡进行满焊,再将声导管安装到方箱上。
见图1.7。
Ifthere’snofireholeonwater-cooledwallcanbeusedasobservationpoint,usuallythespacebetweenwater-cooledwalltubesisnarrow;
inviewofsafefactor,finnednarrowholeonwater-cooledwallcanbebored.Tworectangularholesareboredoncontiguousfinsofverticalwater-cooledwall,andwidthisthesamewithfin’swidth.Makinguseofboxastransitionforfulljointing,thensoundmeatuswillbeinstalledonthebox.Seefigure1.7.
Box
图1.7利用水冷壁鳍片开孔安装声导管
Figure1.7Themethodofboringholewhichmakesuseoffinnedholeonwater-cooledwall
(4)包墙过热器开孔方法
(4)Boringholemakinguseofenclosure-wallsuper-heater
锅炉包墙过热器节距较大,安装声导管时一般不需弯管,只需将鳍片开孔即可。
鳍片开孔时在保证过热器安全的前提下,尽可能使其与声导管口径相同,当鳍片间距小于声导管内径时,鳍片开孔为一椭圆孔,同时将声导管前端适当压扁。
开孔方法见图1.8。
There’sbroadspacebetweenenclosure-wallsuper-heaters,usuallysiphonisnotneededtoinstallsoundmeatus,andfinnedholeisalreadyenough.Whilethesafetyofsuper-heaterisguaranteed,thecaliberoffinnedholeshouldbethesameassoundmeatus’scaliber;
whenthespacesbetweenfinsislessthanthesoundmeatus’sinternaldiameter,finnedholeisboredelliptical,atthesametimethefrontofsoundmeatusshouldbemadeflattofitthehole,seefigure1.8
图1.8利用包墙壁鳍片开孔安装声导管
Figure1.8Themethodofboringholewhichismakinguseofsuper-heaterofenclosure-wall
声导管安装方法TheMethodofInstallingSoundMeatus
(1)侧墙声导管安装方法:
(1)Themethodofinstallingsoundmeatusonside-wall:
侧墙声导管斜段长度大于700mm,现场安装确定实际应留长度。
Thelengthofbeveledgeofsoundmeatusonside-wallshouldbebiggerthan700mm;
actuallengthisdecidedduringinstallation.
声导管的安装原则应保证其上部法兰盘便于安装及检修传感器。
法兰盘上部传感器安装高度为大于300mm(见图1.4)。
Installingsoundmeatusshouldensuretheconvenienceofinstallingandmaintainingthetransducer.Theinstallingheightabovetheflangeshouldbemorethan300mm(seefigure1.4).
安装声导管时应保证声导管根部与水冷壁平齐,不允许声导管伸入水冷壁内侧。
Wheninstallingsoundmeatus,thehemlineofsoundmeatusandwater-cooledwallshouldbekeptatthesamelevel.Itisn’tallowedthatsoundmeatusisinsertedintowater-cooledwall.
声导管与包墙护板满焊,固定可靠。
所有侧墙声导管安装时J型声导管与侧墙呈45°
角(仰角45°
),Y型声导管则仰角为30°
角,以避免运行时积灰堵塞声导管通道,影响准确报警。
声导管与侧墙相对位置见图1.4左图。
Soundmeatusandenclosure-wallarefullweld,fixedandcredible.AllangelsbetweenJ-soundmeatusandsidewallare45o(elevationsare45o),elevationanglebetweenY-soundmeatusandsidewallare30o,inordertoavoidashblockingsoundmeatusandaffectingaccuratealarm,seefigure1.4ontheleft.
(2)侧包墙声导管安装方法:
(2)Themethodofinstallingsoundmeatusonside-enclosure-wall:
侧包墙过热器声导管安装方法基本与图1.4相同,鳍片开孔为一椭圆孔,与护板满焊。
Themethodofinstallingsoundmeatusonside-enclosure-wallsuper-heaterisbasicallythesameasfigure1.4,fi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BLD 锅炉 承压管 泄漏 在线 监测 系统 运行 维护 安装 中英文