P4PB 226E.docx
- 文档编号:16531181
- 上传时间:2023-07-14
- 格式:DOCX
- 页数:35
- 大小:315.56KB
P4PB 226E.docx
《P4PB 226E.docx》由会员分享,可在线阅读,更多相关《P4PB 226E.docx(35页珍藏版)》请在冰点文库上搜索。
P4PB226E
TheMainMenu
主菜单
TheMainMenucontainstwelvesetupfunctionsandtwoexitchoices.Usearrowkeystoselecttheitemsandpress
使用箭头键来选择项目,然后按
StandardCMOSFeatures标准CMOS功能设定
Usethismenutosetbasicsystemconfigurations.使用此菜单来设置基本系统配置。
AdvancedBIOSFeatures高级BIOS的功能设定
Usethismenutosettheadvancedfeaturesavailableonyoursystem.使用此菜单来设置您的系统上可用的高级的功能
AdvancedChipsetFeatures高级芯片组功能设定
Usethismenutosetchipsetspecificfeaturesandoptimizesystemperformance.使用此菜单来设置芯片组的特定功能并优化系统性能。
IntegratedPeripherals外部设备设定
Usethismenutosetonboardperipheralsfeatures.使用此菜单来设置板载外部设备的功能。
PowerManagementSetup电源管理设定
Usethismenutosetonboardpowermanagementfunctions.使用此菜单来设置板载电源管理功能。
PnP/PCIConfigurations即插即用与PCI参数设定
UsethismenutosetthePnPandPCIconfigurations.使用此菜单来设置即插即用和PCI配置。
PCHealthStatusPC系统状态
ThismenushowsthePChealthstatus.此菜单显示PC健康状况。
Frequency/VoltageControl频率/电压控制
Usethismenutosetthesystemfrequencyandvoltagecontrol.使用此菜单来设置系统频率和电压控制。
LoadFail-SafeDefaults加载最安全默认设置
UsethismenutoloadtheBIOSdefaultsettingsforminimalandstablesystemoperations.
使用此菜单来加载BIOS的默认设置为最小和稳定系统操作。
LoadOptimizedDefaults加载最优化默认设置
UsethismenutoloadBIOSdefaultsettingsforoptimalandhighperformancesystemoperations.
使用此菜单来加载BIOS默认设置为最优和高性能系统操作。
SetSupervisorPassword设置的管理员密码
Usethismenutosetsupervisorpassword.使用此菜单来设置管理员密码。
Save&ExitSetup保存并退出设置程序
SaveBIOSsettingchangesandexitsetup.保存BIOS设置更改并退出安装程序
ExitWithoutSaving不保存退设置程序
AbandonallBIOSsettingchangesandexitsetup.放弃所有BIOS设置更改并退出安装程序。
StandardCMOSFeatures
标准CMOS功能
Usethearrowkeystohighlighttheitemandusethe
使用箭头键突出显示该项目,并使用
Date日期
Thedateformatis
Day-dayoftheweek,forexampleFriday.Read-only.星期-星期的计算,例如星期五。
只读。
Month-themonthfromJantoDec.月-从1月至12月。
Date-thedatefrom1to31.日-从1到31的日期。
Year-theyear,rangefrom1999to2098.年,一年,范围从1999年到2098年。
Time时间
Thetimeformatis
DriveA/B驱动器A/B
Setthetypeoffloppydriveinstalled.AvailableoptionsareNone,360K,5.25in.,1.2M,5.25in.,720K,3.5in.,1.44M,3.5in.,2.88M,3.5in.
设置安装软盘驱动器的类型。
可用选项为:
没有,360K5.25英寸,1.2M5.25英寸,720K3.5英寸1.44M3.5英寸,2.88M3.5英寸。
HaltOn停止
Determinethesystembehaviourifanerrorisdetectedatboot.Settingsare:
如果在启动时检测到错误时,请确定系统行为。
设置如下:
AllErrorsSystemhaltswhenanyerrorisdetected.检测到任何错误时都系统停止运行。
NoErrorsSystemdoesnothaltforanyerror.任何错误的系统不会停止。
All,ButKeyboardSystemhaltsforallerror(exceptkeyboarderror).所有错误系统停止但键盘除外(除了键盘错误)。
All,ButDisketteSystemhaltsforallerror(exceptdisketteerror).所有错误系统停止但磁盘除外(除磁盘错误)。
All,ButDisk/KeySystemhaltsforallerror(exceptdisk/keyboarderror)所有错误系统停止但磁盘/键盘除外(除磁盘/键盘错误)
IDEPrimaryMaster/SlaveandSecondaryMaster/Slave第一IDE主控制器/从控制器和第二IDE主控制器/从控制器
Press
按
Thespecificationsofyourdrivemustmatchwiththedrivetable.Theharddiskwillnotworkproperlyifyouenterimproperinformationforthiscategory.SelectAutowheneverpossible.IfyouselectManual,makesuretheinformationprovidedisfromyourharddiskvendororsystemmanufacturer.
您的驱动器的规格与驱动器的表必须匹配。
硬盘将无法正常运行,如果您输入此类别的信息不当。
选择尽可能的自动。
如果您选择手动,请确保信息提供从您的硬盘供应商或系统制造商。
IDEPrimarySlaveThesettingsareNone,Auto,Manual.IDE主从设置是:
无,自动、手动。
AccessModeThesettingsareCHS,LBA,Large,Auto.访问模式设置是CHS,LBA,大型自动
CapacityTheformattedsizeofthestoragedevice.容量存储设备的大小的能力。
CylinderNumberofcylinders.柱面柱面数。
HeadNumberofheads.磁头磁头数
PrecompWriteprecompensation.。
硬盘补偿写入预补偿。
LandingZoneCylinderlocationofthelandingzone.磁头停放区磁头停放区的位置。
SectorNumberofsectors.扇区扇区数量
PIOModeThesettingsareMode0/1/2/3/4,Auto.硬盘参数设置是0/1/2/3/4,自动模式。
UltraDMAModeThesettingsareDisabledandAuto.传输模式设置被禁用的模式和自动模式
AdvancedBIOSFeatures
高级BIOS特性
VirusWarning病毒防护
SettheVirusWarningfeatureforIDEHardDiskbootsectorprotection.Ifthefunctionisenabled,anyattempttowritedataintothisareawillcauseabeepandwarningmessagedisplayonscreen.Settings:
DisabledandEnabled.
设置IDE硬盘和引导扇区引导病毒防护功能。
如果启用功能,任何尝试将数据写入将导致蜂鸣和警告消息显示在屏幕上。
设置:
禁用和启用。
CPUL2CacheECCCheckingCPU的二级高速缓存ECC检查
SettheECC(Error-CorrectingCode)featureforLevel2cache.Facilitateserrordetection/correctionwhendatapassesthroughLevel2cache.Settings:
EnabledandDisabled.
设置用于2级缓存的ECC(错误校正码)功能。
方便了错误检测/修改时2级缓存的数据通过。
设置:
启用和禁用。
QuickPowerOnSelfTest快速电源自我检验
ShortenPowerOnSelfTest(POST)cycleandenableshorterbootuptime.AllowBIOStoskipsomecheckitemsduringPOST.Settings:
EnabledandDisabled.
缩短周期自我测试(加电自检)使缩短启动时间。
允许BIOS在开机自检时跳过一些检查项。
设置:
启用和禁用。
First/Second/ThirdBootDevice第一第二/第三引导设备
SetthebootdevicesequenceasBIOSattemptstoloadthediskoperatingsystem.Thesettingsare:
设置设备的启动序列,如BIOS尝试加载磁盘操作系统。
设置如下:
FloppyThesystemwillbootfromfloppydrive.软盘,系统将从引导软盘驱动器。
LS120ThesystemwillbootfromLS-120drive.LS120大容量磁盘,系统将从Ls-120大容量磁盘驱动器引导。
HDD-0ThesystemwillbootfromfirstHDD.硬盘0,系统将从第一个硬盘引导。
SCSIThesystemwillbootfromSCSI.快速总线,系统将从快速总线引导。
CD-ROMThesystemwillbootfromCD-ROM.光盘,系统将从光盘引导。
HDD-1ThesystemwillbootfromsecondHDD.硬盘1,系统将从第二个硬盘引导。
HDD-2ThesystemwillbootfromthirdHDD.硬盘-2,系统将从第三个硬盘引导。
HDD-3ThesystemwillbootfromfourthHDD.硬盘-3,系统将从第四个硬盘引导。
ZIP100ThesystemwillbootfromATAPIZIPdrive.ZIP100磁盘,系统将从压缩驱动器引导。
USB-FDDThesystemwillbootfromUSBfloppydrive.USB软驱,系统将从USB软盘驱动器引导。
USB-ZIPThesystemwillbootfromUSBZIPdrive.USBZIP,系统将从USB压缩驱动器引导。
USB-CDROMThesystemwillbootfromUSBCDROM.USB光驱,系统将从USB光驱引导。
USB-HDDThesystemwillbootfromUSBHDD.USB硬盘,系统将从USB硬盘引导。
LANThesystemwillbootfromnetworkdrive.局域网,系统将从网络驱动器引导。
DisabledDisablethissequence.已禁用禁用此序列。
BootOtherDevice启动其他设备
EnablethesystemtobootfromotherdevicesifthesystemfailstobootfromtheFirst/Second/Thirdbootdevice.Settings:
EnabledandDisabled.使系统能够从其他设备启动,如果系统无法从引导第一第二/第三的引导设备。
设置:
启用和禁用。
BootUpFloppySeek开机测试软驱
SetfloppyseekduringPOST,BIOSwilldeterminewhetherthefloppyis40or80tracks.Settings:
EnabledandDisabled.
在加电自检期间,BIOS将确定是否软盘40或80的磁道。
设置:
启用和禁用。
BootUpNumLockStatus初始小键盘锁定状态
SettheNumLockstatuswhenthesystemispoweredon.“On”willturnkeypadintonumberkeys,and“Off”willturnkeypadintoarrowkeys.Settings:
OnandOff.设置数字小键盘锁定状态时,系统通电。
"开"将把密钥键盘数字键,进入和"关"将变为箭头键键垫。
设置:
开和关。
TypematicRateSetting击键速率设置
Setthetypematicrateanddelay.Settings:
EnabledandDisabled.设置输入速率及延迟。
设置:
启用和禁用。
TypematicRate(Chars/Sec)输入速率(字符/秒)
WhenTypematicRateSettingisenabled.Thisitemallowsyoutosettherate(characters/second)atwhichthekeysareaccelerated.Settings:
6,8,10,12,15,20,24and30.按键重复速度设置。
此项允许你设置按键重复的速度(字符/秒)设置:
6、8、10、12、15、20、24、30。
TypematicDelay(Msec)按键延迟(毫秒)
WhenTypematicRateSettingisenabled.Thisitemallowsyoutoselectthedelaybetweenwhenthekeywasfirstpressedandwhentheaccelerationbegins.Settings:
250,500,750and1000.
当启用按键速度设置。
此项允许您选择当第一次按下键和重复开始时之间的延迟。
设置:
250、500、750、1000。
SecurityOption检查密码方式
SpecifiesthetypeofBIOSpasswordprotectionthatisimplemented.Settingsaredescribedbelow:
指定类型的BIOS的密码保护,实现。
设置详述如下:
Option选择
Description描述
Setup设置
ThepasswordpromptappearsonlywhenenduserstrytorunSetup.
密码提示出现只有当用户尝试运行安装程序。
System系统
ApasswordpromptappearseverytimewhenthecomputerispoweredonorwhenenduserstrytorunSetup.密码提示出现每次计算机上电或当用户尝试运行安装程序。
DisplayFullScreenLogo全屏显示标志
ShowfullscreenlogoduringBIOSbootupprocess.Settings:
EnabledandDisabled.
全屏显示在BIOS启动过程标志。
设置:
启用和禁用
DisplaySmallLogo显示小标志
ShowsmallenergystarlogoduringBIOSbootupprocess.Settings:
EnabledandDisabled.
:
显示小能源之星在BIOS启动过程标志。
设置:
启用和禁用
AdvancedChipsetFeatures
高级芯片组设置
TheAdvancedChipsetFeaturesmenuisusedforoptimizingthechipsetfunctions高级芯片组功能菜单用于芯片组功能优化
AGPApertureSizeAGP显卡内存
ThissettingcontrolsjusthowmuchmemoryspacecanbeallocatedtoAGPforvideopurposes.TheapertureisaportionofthePCImemoryaddressrangededicatedtographicsmemoryaddressspace.HostcyclesthathittheaperturerangeareforwardedtotheAGPwithoutanytranslation.Settings:
4MB,8MB,16MB,32MB,64MB,128MB,and256MB.
此设置控制系统RAM有多少内存空间可以分配给AGP视频显示用。
口径是PCI内存地址范围的一部分专用于图形内存地址空间。
进入口范围内的主时钟周期会不经过翻译直接传递给AGP。
设置:
4MB,8MB16MB、32MB,64MB,128MB和256MB。
AGPModeAGP模式
ThismainboardsupportstheAGP4xinterface.WhentheAGP4xvideocardisused,itcantransfervideodataat1066MB/s.AGP4xisbackward-compatible,leavethedefault4xmodeonifunsure.Whensetto1xmode,themaximumtransferrateitat266MB/s,and2xmodetransfersdataat533MB/s.Settings:
4X,2Xand1X.
本主板支持AGP4x接口。
AGP4x显卡时,使用它可以传输视频数据,1066MB/s.AGP4x是向后兼容如果不确定上留下4x的默认模式。
任何时设置为1x模式,最大值传输速率它在266MB/s和在533MB/s.设置2x模式。
传输数据:
4X、2X和1X。
AGPDrivingControlAGP驱动控制
ThesettingisusedtoadjustAGPdrivingforce.SelectingManualallowsyoutotypeaAGPdrivingforceinAGPDrivingValue.ItisstronglysuggestedtoselectAutotoavoidcausinganysystemerror.Settings:
AutoandManual.设置用于调节AGP的驱动力。
选择手动允许你输入AGP的AGP驱动控制驱动力。
强烈建议选择自动,以免造成任何系统错误。
设置:
自动和手动。
CPUtoPCIPOSTWriteCPU总线快速写入
WhenEnabled,CPUcanwriteuptofourwordsofdatatothePCIwritebufferbeforeCPUmustwaitforPCIbuscycletofinish.IfDisabled,CPUmust
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- P4PB 226E 226