英语压力容器常用词汇.docx
- 文档编号:14589381
- 上传时间:2023-06-24
- 格式:DOCX
- 页数:60
- 大小:61.49KB
英语压力容器常用词汇.docx
《英语压力容器常用词汇.docx》由会员分享,可在线阅读,更多相关《英语压力容器常用词汇.docx(60页珍藏版)》请在冰点文库上搜索。
英语压力容器常用词汇
压力容器专业词汇
A B类 Category A B安全阀 Safety valve
安装 Installation 鞍式支座 saddle support
凹面 concave 半球形封头 Hemispherical heads
棒 bars 保温支撑 insulation support
爆炸性 explosive 泵 pump
变径段 reducers 标记 stamping
标志 marking 标志的移植 Transfering marking
波纹板 Corrugating Paper 补强管 reinforcing nozzle
补强圈 reinforcing ring 不锈钢 stainless steel
不圆度 out-of-roundness 材料 materials
材料证明书 Certification of material 超声检验 Ultrasonic Examination
衬里 Linings 成型 Forming
成型封头 Formed heads 尺寸 Dimensions
翅片管 finned tubes 冲击试验 impact test
储罐 storage tank 传热面积 heat transfer surface
磁粉检验 Magnetic Particle Examination 次要应力 secondary stress
粗糙度 roughness 淬火 Quenching
带折边的锥形 toriconical 弹簧 springs
弹簧垫圈 spring washer 弹性模量 modulus of Elasticity
挡板 baffle plate 低合金钢容器 low alloy steel vessels
低温容器 Low-temperature vessels 地震烈度 seismic intensity
垫板Backingstrip垫片gasket
垫圈washer碟形封头Dishedheads
顶丝jbckscrew定距管spacer
定位销pindowel定义Definitions
毒性toxicity镀锌容器Galvanizedvessels
锻件Forgings对焊法兰weldingneckflange
耳座lug阀门valves
法兰flanges法兰接触面Flangecontactfacings
防冲板impingementbaffle防腐蚀衬里Corrosionresistantlinings
防火fireprotection防涡流挡板vortexbreaker
非受压件nonpressureparts非圆形容器Noncircularvessels
峰值应力peakstress腐蚀裕量corrosionallowance
附加载荷supplementaryloading附件attachments
复合板Cladplate覆层容器cladvessels
盖板Coverplates杆rodsorbars
过渡段transitionin过渡圆角Knuckles
焊后热处理afterpostweldheattreating焊接工艺weldingprocedurespecification
焊接接头weldingjoints焊接系数weldingcoefficient
厚度thickness滑动的sliding
环向应力hoopstress回火tempering
基本地震加速度basicseismicacceleration基本分压basicwindpressure
计算厚度calculatedthickness技术条件formofSpecification
加强圈 stiffening rings 夹套容器 Jacketed vessels
检查孔 Inspection openings 检验 inspection
角焊 Fillet welds 接地板 earth lug
截止 Stop valves 介质特性 fluid property
金属温度 Metal temperature 筋板 rib plate
径向应力 radial stress 静(压力)水头 static head
局部 areas 局部 local
局部焊后热处理 Local postweld heat treatment 矩形设计 rectangular design
卡箍 clamp 开孔补强 reinforcement for openings
快开盖 Quick-actuating closures 拉杆 tie rod
裂缝 Cracking 流体(介质) fluid
螺孔 holes for screw 螺母 nut
螺塞 plug 螺栓 bolt
螺纹 threaded 螺柱 studs
名义厚度 nominal thickness 铭牌 Name plates
内部构件 Internal structures 内衬筒 internal shell
盘管 coil tube 配件 fittings
膨胀节 expansion joint 平封头 Flat heads
评定 Qualification 气孔 Porosity
气压试验 Pneumatic test 钎焊 brazing
强度 strength of 球形封头 spherically dished
曲率 curvature 屈服 yielding
全容积 total volume 缺陷 defects
群座 skirt support 热处理 thermal treatment
热处理 heat treatmen 热应力 thermal stress
人孔 manholes 韧性 ductility
容积 volume 容器 vessel
容器净重 empty weight 容器类别 vessel classification
塞焊 Plug welds 设计压力 design pressure
射线超声检验 Radiographic Examination 渗透检验 Penetrant Examination
石墨 graphite 试样 Test coupons
适用范围 Scope 手孔 (ha)ndholes
水压试验 hydrostatic test/hydraulic test/hydrotest 碳钢 carbon steel
搪玻璃容器 enameled vessels 梯子、平台 ladders, platforms
填充金属 filler metal 筒体 shell
凸面 convex 凸缘 socket
椭圆封头 Ellipsoidal heads 外压容器 vessels subjected to external pressure
未注尺寸公差 tolerance grade n0t noted 无支撑 unstayed
系数 fact0r 现场安装 Fie1d assemb1y
校核 checking 0f 泄放 (Disc)harge
泄压装置 Pressure relieving (dev)ices 性能 properties
许用工作压力 al1owable working pressure 许用应力 al1owable stress
易然的 flammable 应力腐蚀 stress corrosion
应力集中 stress concentration 预热 Preheating
圆度 roundness 圆角和倒角 corners+fillets
载荷 Loadings e(xpa)nded c0nnections 折流板 baffle plate
蒸发器 (Evap)orators 直边长度 length 0f skirt
直径 Diameter 制造 fabrication
制造厂 fabricator 制造方法 methods 0f fabrication
制造工艺 fabrication technology 周长 Girth
主应力 primary stress 柱状壳体 Cylindrical shells
铸铁容器 cast iron vessels 转角半径 knuckle radius
装配 assembling 锥度 tapered
锥壳 conical shell 锥形封头 Conical heads 资格 qualification
纵向接头 Longitudinal joints 组对 fitting up
无损检测专业词汇
a cluster of flaws 密集区缺陷
A.C magnetic saturation 交流磁饱和 ablution 清洗
Absorbed dose rate 吸收剂量率 Absorbed dose 吸收剂量 Acceptanc limits 验收范围
Acceptance level 验收水平 验收标准 acceptance specification 验收规范 Acceptance standard 验收标准
Accessories 附件 配件 辅助设备 辅助器材 Accumulation test 累积检测 Accuracy 精确度 准确度 acetone 丙酮
Acoustic emission (AE) 声发射
Acoustic emission count 声发射计数
Acoustic emission transducer 声发射换能器 Acoustic holography 声全息术
Acoustic impedance matching 声阻抗匹配 Acoustic impedance method 声阻法 Acoustic impedance 声阻抗 Acoustic wave 声波 Acoustical lens 声透镜
Acoustic-ultrasonic 声-超声(AU) across 交叉 横过 Activation 活化 Activity 活度
additional stress 附加应力 address:
地址:
?
Adequate shielding 适当防护、适当屏蔽 AE 声发射
air header 集气管
"air set 空气中凝固, 常温自硬 自然硬化" air supply 气源 aisle 过道 走廊
alarm condition 报警状态 alarm level 报警电平
Alignment 对准 定位调整 校直 alkaline battery 碱性电池
allowable variation 允许偏差 容许变化 alternating current 交流电 aluminum powder 铝粉 amount 数量
Ampere turns 安匝数
amplifier panel 放大器面板 Amplitude 振幅、幅度 analyzer 分析器
anchor bolt 锚定螺栓 地脚螺栓
Angle beam method 斜射法、角波束法 Angle beam probe 斜探头、角探头 angle fitting 弯头 angle iron 角钢 角铁
Angle of incidence 入射角 Angle of reflection 反射角 Angle of spread 扩散角
Angle of squint 偏向角、偏斜角 Angle probe 斜探头、角探头 angle square 角尺 angle steel 角钢
Angstrom unit 埃(长度单位) appearance 外观
application drawing 操作图 应用图
arc cutting 电弧切割 arc gouging 电弧刨削 arc starting 起弧 arc welding 电弧焊
Area amplitude response curve 面积振幅响应曲线 Area of interest 评定区、关注区域 argon arc welding 氩弧焊
Arliflcial disconlinuity 人工不连续性、人工缺陷 arrangement diagram 布置图
arrival time interval(Δtij) 到达时间差(Δtij) Artifact 人为缺陷
Artificial defect 人工缺陷 A-scan A型扫描 A-scope A型显示 assembly 装配 At present 目前
Attenuation coefficient 衰减系数 Attenuator 衰减器
Audible leak indicator 音响泄漏指示器
automatic temperature recorder 温度自动记录器 Automatic testing 自动检测
Autoradiography 自动射线照相术 axiality 同轴度 轴对称性 axonometric drawing 轴测图 back-feed 反馈
background target 目标本底 background 背景 本底
backwall echo 底波 底面回波 baiting valve 放料阀 band plate 带板
banjo fixing 对接接头 Barium concrete 钡混凝土 Barn 靶
Base fog 片基灰雾 base material 基底材料
basic sensitivity 基准灵敏度 Bath 槽液、浴池、槽
Bayard-Alpert ionization gage B-A型电离计 Beam angle 波束角、束张角 Beam axis 声束轴线
Beam path location 声程定位、声束路径位置 Beam path 声程、声束路径 Beam ratio 光束比 Beam spread 声束扩散
arc cutting 电弧切割 arc gouging 电弧刨削 arc starting 起弧 arc welding 电弧焊
Area amplitude response curve 面积振幅响应曲线 Area of interest 评定区、关注区域 argon arc welding 氩弧焊
Arliflcial disconlinuity 人工不连续性、人工缺陷 arrangement diagram 布置图
arrival time interval(Δtij) 到达时间差(Δtij) Artifact 人为缺陷
Artificial defect 人工缺陷 A-scan A型扫描 A-scope A型显示 assembly 装配 At present 目前
Attenuation coefficient 衰减系数 Attenuator 衰减器
Audible leak indicator 音响泄漏指示器
automatic temperature recorder 温度自动记录器 Automatic testing 自动检测
Autoradiography 自动射线照相术 axiality 同轴度 轴对称性 axonometric drawing 轴测图 back-feed 反馈
background target 目标本底 background 背景 本底
backwall echo 底波 底面回波 baiting valve 放料阀 band plate 带板
banjo fixing 对接接头 Barium concrete 钡混凝土 Barn 靶
Base fog 片基灰雾 base material 基底材料
basic sensitivity 基准灵敏度 Bath 槽液、浴池、槽
Bayard-Alpert ionization gage B-A型电离计 Beam angle 波束角、束张角 Beam axis 声束轴线
Beam path location 声程定位、声束路径位置 Beam path 声程、声束路径 Beam ratio 光束比 Beam spread 声束扩散
buckling deformation 翘曲变形 buried depth 埋深
burn through 烧蚀 烧穿 bus duct 母线槽 butt joint 对接
butt jointing 对接接头 butt weld 对接焊缝 butt welding 对接焊 cable armor 电缆铠装
cable channel 电缆槽 电缆管道 cable fitting电缆配件 cable gland 电缆衬垫 cable laying 电缆敷设
cable routing电缆路由选择 Cable sheath 电缆包皮层
cable testing bridge 电缆测试电桥 cable tray 电缆盘
cable trunk 电缆管道 电缆主干线 calculation sheet 计算书
Calibrated Density Reference Scale 标准密度校验片 Calibration instrument 校准仪器 calorimeter 热量计
Capillary action 毛细管作用 Capping ends 顶盖末端 carbon steel tube 碳钢管 carbon steel 碳钢 Carrier fluid 载液
Carry over of penetrate 渗透剂转入 cascade connection 串联连接 Cassette 暗盒 Cathode 阴极
cathodic protection system 阴极保护系统 caulking metal 填隙合金[金属](材料) CCD Camera 电荷耦合摄像机 cement lined piping 水泥衬里管线 center bearing bracket 中心支架 center line 中心线
center plate 中心板 拨盘
Central conductor method 中心导体法
Central conductor 中心导体 中线(三相四线制) centralized 集中的
centripetal canting pull rope 向心斜拉索 certification of fitness 质量合格证书 channel bases沟渠基底
channel steel expansion ring 槽钢胀圈 Characteristic curve of film 胶片特性曲线 Characteristic curve 特性曲线
Characteristic radiation 特征辐射 标识辐射
Charge Coupled Device 电荷耦合器件(简称CCD) "check against 检查, 核对" check valve 止回阀 Chemical fog 化学灰雾 chipping 修琢
chronometer精密计时表 Ci 居里
Cine-radiography 射线(活动)电影摄影术 连续射线照相 Circuit breaker断路开关 circular array 圆形阵列
Circumferential coils 圆环线圈
Circumferential field 周向磁场 环形磁场 circumferential joint 周圈接缝
Circumferential magnetization method 周向磁化法 circumferential weld 环焊缝 civil engineer 土木工程师
civil works 土建工程 建筑工程 clamp 夹钳
clamping fixture 胎具 夹具 Clean 清理 Clean-up 清除
Clearing time 定透时间 coaxial cable 同轴电缆 cockle stairs 螺旋梯 Coercive force 矫顽力
Coherence length 相干长度(谐波列长度) Coherence 相干性 Coil method 线圈法
Coil reference 线圈参考(参照线圈) Coil size 线圈尺寸 Coil spacing 线圈间距
Coil technique 线圈技术 线圈法 Coil test 线圈试验
Coincidence discrimination 符合性鉴别 一致性鉴别 cold lap 冷隔
Cold-cathode ionization gage 冷阴极电离计 collar e
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 英语 压力容器 常用 词汇