焚烧炉操作说明.docx
- 文档编号:13565724
- 上传时间:2023-06-15
- 格式:DOCX
- 页数:2
- 大小:14.66KB
焚烧炉操作说明.docx
《焚烧炉操作说明.docx》由会员分享,可在线阅读,更多相关《焚烧炉操作说明.docx(2页珍藏版)》请在冰点文库上搜索。
焚烧炉操作说明
焚烧炉操作说明
1.加热废油柜至60℃以上,打开废油柜出口阀和点火柴油进口阀。
2.将柴油“置换”开关置于“正常”位。
3.点火油头开关(辅助)放于“正常”位。
4.把所有“手动”放于“自动”位。
5.把废油压力调节阀和流量调节阀全开。
6.打开电源开关,打开雾化空气阀等。
7.按下“复位”开关。
8.按下“自动启动”开关。
9.排烟风机和废油泵将运转,调节废油压力至0.06MPa。
10.废油开始燃烧后,调节废油流量,控制炉膛温度900~950℃
11.当需要停止时,按下“自动停止”按钮。
要停止前,需用轻油置换废油。
当炉膛温度低于50℃时,排烟风机自动停止。
12.关闭相关阀门。
OPERATIONOFINCINERATOR
Methodofincineratingwasteoil
1.Heatingwasteoiltankupto60℃,Openthewasteoiltankoutletvalveandpilotburnerdieseloilinletvalve.
2.Putthedieseloilsubstitutionswitchin“Nor.”Position.
3.Putthepilotburnerswitch(Assist)in“Nor.”position.
4.PutallmanualoperationswitchesinAutoposition.
5.Putthewasteoilpressureregulatingvalveandwasteoilflowregulatingvalveinfullopenposition.
6.Turnonpowerswitch,Openmainvalveasatomizingairmainvalveetc.
7.Presstheresetswitchtomaketheinitialreset.
8.PressAUTOSTARTswitch.
9.Theinducedfanandwasteoilpumpwillstartonrunning.Atthistime,regulatethecirculatingpressureofwasteoilto0.06MPa.
10.Afterstartingthecombustionofwaistoil,regulatetheflowofwasteoilsothatthecombustionchamberoutletexhaustgastemperaturewillfallwithintherangeof900to950℃.
11.Wherewasteoilincinerationhastobeallowedtostop,pressAUTOSTOPswitch,beforestopincinerating,substitutedieseloilforwasteoil.Whenthecombustionchamberoutletexhaustgastemperaturehasarrivedat50℃,theinducedfancomestoastopautomatically.
12.Closesuchmainvalvesasatomizingairmainvalve,dieseloilvalve,etc.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 焚烧 操作 说明