3D打印机175耗材操作手册中英文.docx
- 文档编号:13011497
- 上传时间:2023-06-10
- 格式:DOCX
- 页数:18
- 大小:5MB
3D打印机175耗材操作手册中英文.docx
《3D打印机175耗材操作手册中英文.docx》由会员分享,可在线阅读,更多相关《3D打印机175耗材操作手册中英文.docx(18页珍藏版)》请在冰点文库上搜索。
3D打印机175耗材操作手册中英文
3D打印机
操作手册
3DPRINTER
MANUALNSTRUCTION
2016-1-5[版]
第一步、打印机组装
FIRSTSTEP.PRINTERASSEMBLY
1、耗材托架的安装
1.InstallationofConsumableBracket
上组图中,左图为耗材托架,右图为耗材托架的安装位置,安装位置在打印机后侧机盖上。
Asshownabove,leftpictureisconsumablebracket,andtherightpictureisInstallationlocationoftheconsumablebracketwhichisonthebackofprintermachinecover.
2、送料管的安装
2.InstallationofTransferMaterialPipeline
上图所示位置在打印机后侧机盖上,白色的就是送料管,主要作用是为耗材提供输送通道。
快接头主要是用来固定送料管,防止送料管上下移动。
Theinstallationwhichisshownaboveisonthebackofprintermachinecover,thewhitetubeisthetransfermaterialpipeline,itisdesignedfortransfertheconsumable.Quickconnectorisdesignedforfixedthetransfertubeandpreventverticalmovement.
注:
安装时送料管时,将送料管捅到底即可,插入长度约在一公分左右。
送料管的另外一端在安装好耗材之后进行安装,(后期如遇更换耗材或其他操作,需要将送料管拔出的情况时,需先将快接头上的塑料圈按下,之后才能将送料管拔出)。
Note:
Pleaseinstallthetransfermaterialpipelinetothebottomofquickconnectoranditisabout1cm.Theotherendofthetransfermaterialpipelineinstalledaftertheconsumableinstallation.(Ifchangetheconsumableorotheroperation,pleasepresstheplasticringdownbeforepulloutthetransfermaterialpipeline.)
第二步、打印机平台调平
SECONDSTEP.ADJUSTPRINTEROPTICALFLATNESS
说明:
打印机平台调平一次之后,一般情况下不用重复调平。
不过在运输过程中因为颠簸抖动,可能会导致平台的平整度发生变化,所以在使用之前建议先进行检查调平操作。
Instruction:
Usuallyyoudonotneedtoadjusttheopticalflatnessafterfirstadjustment.werecommendtocheckthestatuscausedbytransportation.
1、调平前准备
1.AdjustmentReady.
首先检查喷嘴,保证喷嘴外表面洁净,没有赘余的耗材等物。
如下图(左)所示,喷嘴处的赘余物可以用剪钳等工具剔除掉。
达到如下图(右)所示即可。
Firstcheckingthenozzleandmakesureit’scleanonthesurface.Asshownbelow(Left),Usepliersandothertoolstoweedouttheremainder.asshownbelow(Right).
2、控制打印机辅助调平
2.PrinterAssistAdjustLevelControl
首先需要为3D打印机通电,3D打印机所使用的是普通220V家用电,直接接入即可。
该款3D打印机屏幕为触控屏幕,下图(左)为主界面,点击“工具”,选择“调平”如下图(右)。
Powerupsthe3Dprinterfirst,3Dprinterusehomevoltage220V.
This3Dprinteristouchscreenmodel,Themainmenuasshownbelow(Left),Clickthe“TOOLS”,selecte“ADJUSTMENT”asshownbelow(Right).
随后会出现如下图(左)所示界面,点击“NEXT”,当喷头每次移动到一个微调螺母上方时,进行平台的微调,微调螺母如下图(右)所示。
Thenclick“NEXT”asshownbelow(Left),Adjusttheplatformwhenthenozzlemovetothelocationabovethefineadjustmentnut.asshownbelow(Right).
平台上共分布着三个微调螺母,随着“NEXT”的点击,喷头会依次移动到微调螺母上方,每个点调节到如下图所示距离即可,或者可以将一张A4纸对折后,放在喷头和平台之间,调节时,适当抽拉纸张,纸张刚好可以轻松的抽出来的时候,说明喷头和平台的距离基本合适了。
也可以以玻璃平台上喷头的倒影和喷头实体之间的距离作为参照进行调节。
Theredistribute3fineadjustnuts,thenozzlewillmoveabovethenutsinturns,
Adjusteachoftheregulatorypointasshownbelow,OrfoldapieceofA4paperandplaceitbetweennozzleandplatform.ifyoucandrawoutthepapergently,it
provesthenozzlefitthebasicplatform.
YoucanalsoAdjustitbythereflectionontheglassplatformsprinklersandnozzlesentitiesasareference.
注:
微调螺母的原理:
微调机构由螺丝、蝶形螺母、弹簧三部分组成。
当螺母拧[紧]的时候,平台便会向[下]方移动,从而拉[远]喷头和平台的间距;
当螺母拧[松]的时候,由于弹簧的弹性作用,便会将平台向[上]方顶起,从而拉[近]喷头和平台的间距;
Note:
Theoryoffineadjustmentnuts:
Fineadjustmentmechanismbyscrews,wingnuts,springs.
Screwingthenuts,theplatformwillmovedown,itwillpullawaythedistancebetweennozzleandplatform.
Looseningthenuts,theplatformwillmoveup,causedbyspringaction,itwillshrinknearlythedistancebetweennozzleandplatform,
第三步、耗材的安装及岀丝测试
THIRDSTEP.CONSUMABLESINSTALLATIONANDTESTINGEXTRUDER
1、喷头加热
1.HEATINGNOZZLE
通过打印机显示屏控制喷头加热,如下图(左)所示点击“预热”,随后出现如下图(右)所示界面。
Controlheatingnozzlebyprinterscreen,Clickthe“Pre-Heating”asshownbelow(Left),itwilldisplaythefollowinterface,asshownbelow(Right).
如上图(右)所示。
第一行为平台的温度控制选项,数字表示平台的“当前实际温度/设置温度”;
第二行为喷头的温度控制选项,数字表示喷头的“当前实际温度/设置温度”;
其中向上(向下)的箭头,分别表示提升(降低)温度。
现在需要将平台的“设置温度”设置到64度,将喷头的“设置温度”设置到205度。
如下图所示。
Asshownabove(Right).
Thefirstlinearetheplatformtemperaturecontroloptions,thenumbersshownonthescreenare“TEMP/TEMPSETTING”;
Thesecondlinearetheplatformtemperaturecontroloptions,thenumbersshownonthescreenare“TEMP/TEMPSETTING”;
TheUPandDOWNarrowsstandsforliftingandloweringthetemperature.Settheplatformtemperatureto64℃,thensetthenozzletemperatureto205℃。
Asshownbelow.
2、耗材的处理
2.DealingwithConsumables
将耗材从包装盒内取出后,将耗材的端部用剪钳剪出一个斜口,以便于耗材的送入。
另外耗材的端部约五公分的长度需略微的握直,也是便于耗材的送入。
如下图所示。
Takingtheconsumablesoutofthepackagingbox,andForinserteasily,cutoutaninclineononesideandstraightgriparound5cmfromtheendoftheotherside.
asshownbelow,
将耗材挂在耗材托架上,然后将耗材从打印机后侧机盖的快接头下方送入如下图(左)所示。
耗材从送料卡下方送入,然后用手将送料卡捏住,如下图(右)所示。
之后将耗材继续向内穿入,直至从送料管的另外一端穿出。
Hanguptheconsumablesonthebracket,theninsertittoquickconnectoronthebackoftheprinter.Inserttheconsumablesacrossthebackoftransportationcard,
Pinchthetransportationcard,asshownbelow(Right).Inserttheconsumableuntilit
penetratefromtheothersideofthetransportationpipeline.
耗材从从送料管另外一端穿出后,将耗材从喷头上方的快接头处穿入,如下图(左)所示。
随后即可将送料管插入快接头固定,插入长度约在五公分左右。
如下图(右)所示。
Inserttheconsumablefromthequickconnectoronthetopofthenozzle,afterpenetratethetransportationpipelineformtheothersideoftheconsumables.asshownbelow(Left).Thenfixedthetransportationpipelineafterinsertthequickconnector,Theinsertlengthisabout5cm.asshownbelow(Right).
注:
后期如遇更换耗材等操作,需要将送料管拔出的情况时,需先将快接头上的塑料圈按下,之后才能将送料管拔出。
Note:
Ifchangetheconsumableorotheroperation,pleasepresstheplasticringdownbeforepulloutthetransfermaterialpipeline.
3、测试岀丝
3.TestingExturder
通过打印机显示屏控制挤出机的转动,也就是控制E轴转动。
如下图(左)所示,图中“1010.1”表示电机单次转动的距离。
单位为毫米,建议测试岀丝的时候选择10或1。
选好后按击“E↓“,之后会发现喷嘴处会有耗材挤出,如下图(右)所示。
Controltheturnofextrusionmachinebyprinterscreen,ThatiscontrolEaxisturnrate.asshownbelow(Left),asshown‘10mm’’1mm’’0.1mm’itstandsformotorrotationdistanceforeachtime.theunitismm.Werecommendselect10mmor1mmfortestingextruder.Click‘E↓’afterselection,asshownbelow(Right),itwillappearsomeconsumablefromnozzle.
直至挤出的耗材顺滑均匀即可。
至此耗材的安装及岀丝测试结束。
下面进行模型的打印。
Untiltheconsumablecomesoutsmoothlyanduniformfromtheextruder.Thuswefinishtheconsumablesinstallationandextrudertesting.Thefollowingstepisprintmodel.
第四步、模型的打印
1、打印前准备
1.PreparationBeforePrinting
将所要打印的模型导入“切片软件”中,进行打印参数设置,之后导出打印机可以识别的“Gcode”文件,“切片软件”的操作参考“切片软件操作教程”,这里仅给出该款3D打印机适用的参数设置。
Insertthemodelprintreadyto‘Slicingsoftware’,Exportthe‘Gcode’fileaftersetuptheprintparameters,ForHowtouse"Slicingsoftware,"pleasereferencethesectionofthesoftwareoperationtutorial".Belowisthe3Dprintermacinesettingsparameters.
将导出的“Gcode”文件拷贝入SD卡,然后将SD卡插在打印机上如下图所示。
Copytheexportedfile‘Gcode’toSDcard,andinsertittoPrinter,asshownbelow.
之后用打印机箱内配备的胶棒,如下图(左)所示,在平台上所要打印模型的区域进行涂抹,如下图(右)所示。
Daubtheprintingareawithequippedgluestick,asshownbelow.
2、打印模型
2.PrintModel
在打印机屏幕上,选择“打印”如下图(左)所示;
如下图(右)所示,选择要打印的模型文件后;
如下图(下)所示,点击中间的按钮,打印机便会开始按照文件内的指令自主进行打印。
Select’PRINT’fromtheprinterscreen,asshownbelow(LEFT);
Asshownbelow(RIGHT),Afterselectedtheprintingfile;
Asshownbelow(DOWN),Clickthemiddlebutton,theprinterwillAuto-Startprintingaccordingtheinstructionoftheprintingfile;
3、打印完成后的处理
3.CompletedProcessing
打印完成后,用配备的平铲将模型从平台上铲下即可,如下图所示。
Afterprintingiscomplete,Shovelthemodeldownfromtheplatformwithequippedflatshovel,asshownbelow.
注:
建议每次打印前都先进行喷头的加热及岀丝测试,保证打印机耗材输送正常,保证打印的模型的质量。
Note:
Astoensurethetransportationofprinterconsumablesinnormalworkandmakesurethequalityofprintingmodel,westronglyrecommendheatingnozzleandtestingextruderbeforeeachitem.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 打印机 175 耗材 操作手册 中英文
![提示](https://static.bingdoc.com/images/bang_tan.gif)