基于PLC的交通灯控制系统设计外文翻译.docx

基于PLC的交通灯控制系统设计外文翻译.docx

《基于PLC的交通灯控制系统设计外文翻译.docx》由会员分享，可在线阅读，更多相关《基于PLC的交通灯控制系统设计外文翻译.docx（14页珍藏版）》请在冰点文库上搜索。

1、 毕业设计（外文翻译 ） 英文题目 PLC-based design of traffic lights 中文题目 基于 PLC 的交通灯设 计 系 （院） 自动化系 专 业 电气工程与自动 化 学生姓名 学 号 2009022388 指导教师 职 称 讲 师 二 一三 年 六 月 1 PLC-based design of traffic lights Abstract: One kind of traffic light control system using programmable logic controller (PLC), via software control traffi

2、c lights run automatically. In the system, the original line is the program instead of the relay, programmable logic controller (PLC) system hardware and software resources to be fair use. Normal operation and emergency transport for a detailed description and from the East and West emergencies can

3、be mutually linked. Traffic signal systems and two seven-segment digital display in the countdown order; also discussed in detail the wiring of the hardware and PLC ladder. Traffic lights at the crossroads of the remote monitoring system design configuration software MCGS, real-time monitoring of tr

4、affic lights, greatly improving the reliability of data transmission. At the same time, we can configure the traffic lights to change the status of photographs. Keywords: switching power,supply protection, circuit system design 2 1. Introduction With the social development and progress, traffic flow

5、 becomes increasingly important. On the one hand, too many crossroads, more and more vehicles, which are causing serious traffic congestion. On the other hand, in the limited time it is necessary to maintain the vehicle and pedestrian fast and safe. Therefore, one kind of traffic light control syste

6、m design, can be used to display time countdown, with computer controlled real-time data. In addition, the configuration technology for real- time images that reflect the traffic lights, understand the historical crossroads of work to get traffic lights visualization. The system consists of host com

7、puter and a low computer. MCGS configuration is installed in the host computer is lower by the PLC control system. Normal traffic signal timing diagram shown in Figure 1. But there are some urgent matters, for example. There are a number of ambulances to transport patients to the hospital or to deal

8、 with a number of fire engines and fire. Fire engines and ambulances rushed to take precedence over other traffic scene. According to urban traffic control system, under normal circumstances, two control methods and urgency traffic control factors into account. This process can show 14 segment encod

9、er. U.S. traffic lights instant record of the monitoring process. Emergency control signals to control traffic emergency switch. If there is no emergency lights all work, but when an emergency open. In this case, the car is urgent priority pass. Once the emergency vehicle passes, emergency switch of

10、f immediately. The green light in the same direction of the vehicle quickly flashes three times, followed by the normal operation. If you were from the north-south and east-west two emergency vehicles, traffic control systems can respond quickly came early, and then another. 2. Traffic Control Syste

11、m Design A. Hardware design CP1H series PLC as controller, display the procedure should stop when the time series of abnormal system operation, the time will not be displayed. When the emergency procedures are completed time series, countdown display program should be reset. At 220 V AC system is us

12、ed to control traffic lights, 24 V DC control segment encoder, Figure 2 shows the scheme Eastern time display. CP1H series programmable logic controller (PLC) is a simple controller, which consists of 24 inputs and sixteen outputs. Because the output to twenty In this system, an I / O 3 module must

13、be extended. Circuit is shown in Figure 2. B. Control Program Design Six timers and two special normal open pulse is used in this system, the green light flashes for all north-south and east-timer and a special pulse; eight kinds of 4 interlocking internal relay is used to implement the urgency and

14、transmit pulse two directions to PLC, shown in the figure. Two SDEC instructions are used to display the countdown display the corresponding light. As an important part of the countdown display program, east and west of the green light reflected in the view 4 in these programs downloaded to the prog

15、rammable logic controller (PLC), all the traffic lights running accuracy, urgency, and things can be interlocked from north to south strictly, all the lights can be set back to the urgency of passing state. Therefore, these control program is correct, simple. C. Monitoring System Computer system has

16、 two main functions: an output signal acquisition and display real-time status of the programmable logic controller (PLC) to control traffic lights, traffic lights. Another notification robot status and history of the state real-time curve by examining the history and alarm window. This monitoring s

17、ystem design and configuration software MCGS configuration is easy. The serial communication is implemented as follows. 5 Data inspection methods: double ended Serial Communications Number: COM0 ended The minimum sampling period: 200 ms Programmable Logic Controller (PLC) The parameters are defined

18、as follows: The minimum sampling period of the basic properties: 200 ms Three read / write channel: X0, X1, X2 Six read-only access (read U.S. traffic lights): Q0-Q5 All channels must be connected to a variable defined in a real-time database access visits and other parameters to their default value

19、s. After a successful relationship, PLC and computer control system is able to change the color of the analog signal lights in the picture on the PC being collected data through the serial port In contrast, by changing the parameters of the host, the corresponding value is written to the PLC interna

20、l relay control, intersection traffic lights can be implemented. Experimental results show that the system is usually good enough and animation. Online monitoring system of traffic lights in Figure 5: 3. Conclusion Experimental results show that the system is usually configured with enough good phot

21、os. This system simplifies the programmable logic controller (PLC) and the communication between the host computer using industrial configuration software development time is greatly reduced. In particular, more suitable for complex control 6 systems. We can control the traffic lights by the PLC and

22、 MCGS configuration, replace the original relay control, improve the systems lifetime. At the same time, this method can be applied to control the motor and fluid levels. Remote control and configuration combined with the simulation, can be applied to similar control zone. 4. References 1 Whitworth,

23、 Duller, Jones D I. Aerial video inspection of overhead power lines J.Power Engineering Journal,2001,15:25-32. 2 Jan Axelson, Lakeview Research-Serial port complete D. USA:1999:91-135. 7 基于 PLC 的交通灯控制系统设计 摘要 一种交通灯控制系统采用可编程序控制器 (PLC), 通过软件控制 交通灯自动运行。在系统原有的继电器线路被程序代替，可编程序控制 器 (PLC)系统的硬件和软件资源的被合理使用。正常运

24、行和紧急运 输进 行了详细的介绍，并从突发事件的东西南北可以相互连锁。交通 灯信号 系统和两个数码管显示在倒计时秩序 ; 同时详细的论述布线 的硬件和 PLC 的梯形图。在十字路口的交通信号灯远程监控系统设 计了组态 软 MCGS，实时监控红绿灯，大大提高了数据传输的可靠性。 与此同时， 我们可以通过合理配置改变交通信号灯的状况。 关键词 ： PLC，交通信号灯， SDEC，配置软件， MCGS 组态 8 一、引言 随着社会的发展和进步 ,交通畅通变得越来越重要。一方面 ,太多的十字路口 , 车辆越来越多，这些都造成严重的交通堵塞。另一方面，在有限的时间有必要保 持 车载和行人快速和安全。因此

25、，一种交通灯控制系统的设计 , 可以用来显示时 间 的倒计时 , 与电脑联网控制实时数据。此外 ,配置技术应用于实时图像反映的交通 信号灯、了解历史工作的十字路口， 获得交通信号灯的可视化。该系统由计 算 机主机和较低的电脑。 MCGS 组态被安装于主机、较低的电脑是由 PLC 控制 系 统。 时序图正常交通信号灯显示图 1，但也有一些紧急的事情。例如有一些救护 车用来运送病人医院或一些消防车用来对付大火。消防车和救护车优先于其他的 交通赶到出事地点，根据城市交通控制系统，正常情况下两种控制方法交通控制 和 紧迫性因素考虑在内。这个过程可以显示了 14 段编码器，美国的交通信号灯的即 时照片记

26、录了监控过程。 紧急控制信号是控制交通紧急开关如果没有紧急事件所有的红绿灯正常工 作，只是紧急事件发生的时候打开。在这种情况下 ,紧急的车是优先通过。一旦 紧急车辆经过 ,应急开关立即关掉。那绿色的光在同一方向的车辆迅速闪三次 ， 随后正常运行。如果从南北和东西分别有两个紧急车，交通控制系统只能迅速反 应 来得早的，然后另一个。 二、交通控制系统的设计 A. 硬件电路设计 CP1H 系列的 PLC 作为控制器 ,，显示的程序应该停止的时候，时间序列异 常系统工作，时间不会被显示。当紧急程序完成了时间序列、倒计时显示的程序 应 该被重置。在 220 V 交流系统是用来控制交通信号灯， 24 V

27、直流控制七段编 码 器，图 2 显示了方案东西方时间显示。 CP1H 系列可编程序控制器 (PLC)的一 个 简单的控制器，它由 24 输入和 16 个输出。因为需要二十输出在这个系统中 , 一个 I / O 模块必须被扩展。线路图如图 2： 9 10 B. 控制程序的设计 六个定时器和两个特殊的正常开启脉冲是用来在这个系统中，绿色灯闪南 北及东西进行所有的定时器和特殊的脉冲；八种内部继电器被用来实现联锁的 紧迫性和发送脉冲两个方向至 PLC，图中显示。两个 SDEC 指示是用来显示倒 计时显示相应的光。作为一个重要的部分 ,倒计时显示程序，东、西向的绿灯表 现在视图 4。在这些程序下载到可编

28、程序控制器 (PLC)，所有的交通灯运行准 确、紧迫性和从南北东西可以联锁严格时，所有的灯都能回到设置的迫切性经 过时的状态。所以这些控制程序是正确的、简单的。 C. 监控系统的设计 计算机系统有两个主要功能： 一个输出信号的采集和显示实时状态的可编 程序控制器 (PLC)控制交通信号灯、交通信号灯，另一个通知机械手的状态和历 史状态实时通过检验历史曲线及报警窗口。 该监控系统的设计和组态软件 MCGS 组态。父亲装置的参数设置的串行通 信的实现如下： 11 12 通信波特率： 6 9600 数据位： 0-7bit,Stop-bit:2-2bit 数据检查方法：双止 串行通信号码： COM0

29、最小的采样周期： 200 毫秒 可编程序控制器的参数定义如下： 最小的采样周期的基本属性： 200 毫秒 三个读 /写渠道： X0、 X1、 X2 六只读通道： Q0-Q5 所有的通道必须连接到变量中定义一个接一个的实时数据库访问和其他参 数的默认值。一个成功的关系后 ,PLC 与计算机控制系统能够模拟信号改变颜色 的灯在这幅画中，在 PC 上被收集到的数据通过串口。然后进行状态监测的十字 路口交通信号灯术。相反 ,通过改变参数的主机、相应的值写入 PLC 内部继电器 的控制、路口交通信号灯能够得到贯彻执行。实验结果表明，该系统通常和动画 13 了足够的好。在线监测系统的交通信号灯如图 5：

30、三、结论 实验结果表明，该系统通常和配置了足够的好照片。该系统简化了可编程序 控制器 (PLC)和计算机主机之间的通信采用工业组态软件开发的时间大大缩短。 尤其是 ,更适合复杂的控制系统。我们可以控制交通信号灯由 PLC 和 MCGS 组态 , 取代原来的继电器控制，提高该系统的寿命。与此同时，可以将此方法应用到控 制电机和液体的水平。远程控制和配置仿真的组合在一起，也可以应用到类似的 控制区域。 参考文献 1 Maman Avishay, Goldschlager Sharon, Miller Hillel可重用的片上系统级验证模拟仿真和硅 . 第 11 届 IEEE 国际高级设计验证和测试研讨会 ,2006 年 ,页 119 126. 2 Jaksic, Nebojsa.提高学生自我效能感在工程运用 PLC 红绿灯实验基础 .2002 ASEE 年度会 议论文集 ,2002 年 ,页 13409 13414.