1、变压器外文翻译摘 要XF 110KV变电所是地区重要变电所，是电力系统110KV电压等级的重要部分。其设计分为电气一次部分和电气二次部分设计。一次部分由说明书，计算书与电气工程图组成，说明书和计算书包括变电所总体分析;负荷分析与主变选择;电气主接线设计;短路电流计算;电气设备选择;配电装置选择;变电所总平设计及防雷保护设计。二次部分由说明书，计算书与电气工程图组成。说明书和计算书包括整体概述;线路保护的整定计算;主变压器的保护整定计算;电容器的保护整定计算;母线保护和所用变保护设计。计算书和电气工程图为附录部分。其中一次部分电气AutoCAD制图六张；二次部分为四张手工制图。本变电所设计为毕业
2、设计课题，以巩固大学所学知识。通过本次设计，使我对电气工程及其自动化专业的主干课程有一个较为全面，系统的掌握，增强了理论联系实际的能力，提高了工程意识，锻炼了我独立分析和解决电力工程设计问题的能力，为未来的实际工作奠定了必要的基础。关键词:变电所；变压器；继电保护AbstractXF county 110KV substation is an important station in this distract, which is one of the extremely necessary parts of the 110KV network in electric power system
3、.The design of the substation can be separated in two parts: primary part and secondary part of the electric design.The first part consists of specifications, computation book and Electrical engineering drawings about the design. The specifications has several parts which are General analysis of the
4、 station, Load analysis, The selection of the main transformer, Layout of configuration, Computation of short circuit; Select of electric devices, Power distribution devices, General design of substation plane and the design of thunderbolt protection.The second part also consists of specifications,
5、computation book and electrical drawings about the design。 Specifications and computation book include following section: General, The evaluation and calculate of line protection, Transformer protection, capacitor protection, Bus protection and Self-using transformer protection.Computation book, Ele
6、ctrical engineering drawings and catalogue of drawings are attached in the end。 There are nine drawings total, in which four are prepared by hand, others are prepared by computer in which installed the software electrical AutoCAD. From other view, it also can be classified as first part and second p
7、art.This is a design of substation for graduation design test. It can strengthen our specified knowledge.Key-words: substation； transformer； Relay protectionTRANSFORMER1. INTRODUCTIONThe high-voltage transmission was need for the case electrical power is to be provided at considerable distance from
8、a generating station. At some point this high voltage must be reduced, because ultimately is must supply a load. The transformer makes it possible for various parts of a power system to operate at different voltage levels. In this paper we discuss power transformer principles and applications.2. TOW
9、-WINDING TRANSFORMERSA transformer in its simplest form consists of two stationary coils coupled by a mutual magnetic flux. The coils are said to be mutually coupled because they link a common flux.In power applications, laminated steel core transformers (to which this paper is restricted) are used.
10、 Transformers are efficient because the rotational losses normally associated with rotating machine are absent, so relatively little power is lost when transforming power from one voltage level to another. Typical efficiencies are in the range 92 to 99%, the higher values applying to the larger powe
11、r transformers.The current flowing in the coil connected to the ac source is called the primary winding or simply the primary. It sets up the flux in the core, which varies periodically both in magnitude and direction. The flux links the second coil, called the secondary winding or simply secondary.
12、 The flux is changing; therefore, it induces a voltage in the secondary by electromagnetic induction in accordance with Lenzs law. Thus the primary receives its power from the source while the secondary supplies this power to the load. This action is known as transformer action.3. TRANSFORMER PRINCI
13、PLESWhen a sinusoidal voltage Vp is applied to the primary with the secondary open-circuited, there will be no energy transfer. The impressed voltage causes a small current I to flow in the primary winding. This no-load current has two functions: (1) it produces the magnetic flux in the core, which
14、varies sinusoidally between zero and m, where m is the maximum value of the core flux; and (2) it provides a component to account for the hysteresis and eddy current losses in the core. There combined losses are normally referred to as the core losses.The no-load current I is usually few percent of
15、the rated full-load current of the transformer (about 2 to 5%). Since at no-load the primary winding acts as a large reactance due to the iron core, the no-load current will lag the primary voltage by nearly 90. It is readily seen that the current component Im= I0sin0, called the magnetizing current
16、, is 90 in phase behind the primary voltage VP. It is this component that sets up the flux in the core; is therefore in phase with Im.The second component, Ie=I0sin0, is in phase with the primary voltage. It is the current component that supplies the core losses. The phasor sum of these two componen
17、ts represents the no-load current, orI0 = Im+ Ie （3-1）It should be noted that the no-load current is distortes and nonsinusoidal. This is the result of the nonlinear behavior of the core material.If it is assumed that there are no other losses in the transformer, the induced voltage In the primary,
18、Ep and that in the secondary, Es can be shown. Since the magnetic flux set up by the primary winding，there will be an induced EMF E in the secondary winding in accordance with Faradays law, namely, E=N/t. This same flux also links the primary itself, inducing in it an EMF, Ep. As discussed earlier,
19、the induced voltage must lag the flux by 90, therefore, they are 180 out of phase with the applied voltage. Since no current flows in the secondary winding, Es=Vs. The no-load primary current I0 is small, a few percent of full-load current. Thus the voltage in the primary is small and Vp is nearly e
20、qual to Ep. The primary voltage and the resulting flux are sinusoidal; thus the induced quantities Ep and Es vary as a sine function. The average value of the induced voltage given byEavg = turns （3-2）which is Faradays law applied to a finite time interval. It follows thatEavg = N = 4fNm （3-3）which
21、N is the number of turns on the winding. Form ac circuit theory, the effective or root-mean-square (rms) voltage for a sine wave is 1.11 times the average voltage; thusE = 4.44fNm （3-4）Since the same flux links with the primary and secondary windings, the voltage per turn in each winding is the same
22、. HenceEp = 4.44fNpm （3-5）andEs = 4.44fNsm （3-6）where Ep and Es are the number of turn on the primary and secondary windings, respectively. The ratio of primary to secondary induced voltage is called the transformation ratio. Denoting this ratio by a, it is seen that a = = （3-7）Assume that the outpu
23、t power of a transformer equals its input power, not a bad sumption in practice considering the high efficiencies. What we really are saying is that we are dealing with an ideal transformer; that is, it has no losses. ThusPm = Pout （3-8）orVpIp primary PF = VsIs secondary PF （3-9）where PF is the powe
24、r factor. For the above-stated assumption it means that the power factor on primary and secondary sides are equal; thereforeVpIp = VsIs （3-10）from which is obtained= a （3-11）It shows that as an approximation the terminal voltage ratio equals the turns ratio. The primary and secondary current, on the
25、 other hand, are inversely related to the turns ratio. The turns ratio gives a measure of how much the secondary voltage is raised or lowered in relation to the primary voltage. To calculate the voltage regulation, we need more information.The ratio of the terminal voltage varies somewhat depending
26、on the load and its power factor. In practice, the transformation ratio is obtained from the nameplate data, which list the primary and secondary voltage under full-load condition.When the secondary voltage Vs is reduced compared to the primary voltage, the transformation is said to be a step-down t
27、ransformer: conversely, if this voltage is raised, it is called a step-up transformer. In a step-down transformer the transformation ratio a is greater than unity (a1.0), while for a step-up transformer it is smaller than unity (a1.0). In the event that a=1, the transformer secondary voltage equals
28、the primary voltage. This is a special type of transformer used in instances where electrical isolation is required between the primary and secondary circuit while maintaining the same voltage level. Therefore, this transformer is generally knows as an isolation transformer.As is apparent, it is the
29、 magnetic flux in the core that forms the connecting link between primary and secondary circuit. In section 4 it is shown how the primary winding current adjusts itself to the secondary load current when the transformer supplies a load.Looking into the transformer terminals from the source, an imped
30、ance is seen which by definition equals Vp / Ip. From 3-11, we have Vp = aVs and Ip = Is/a.In terms of Vs and Is the ratio of Vp to Ip is= = （3-12）But Vs / Is is the load impedance ZL thus we can say thatZm (primary) = a2ZL （3-13）This equation tells us that when an impedance is connected to the seco
31、ndary side, it appears from the source as an impedance having a magnitude that is a2 times its actual value. We say that the load impedance is reflected or referred to the primary. It is this property of transformers that is used in impedance-matching applications.4. TRANSFORMERS UNDER LOADThe prima
32、ry and secondary voltages shown have similar polarities, as indicated by the “dot-making” convention. The dots near the upper ends of the windings have the same meaning as in circuit theory; the marked terminals have the same polarity. Thus when a load is connected to the secondary, the instantaneous load current is in the direction shown. In other words, the polarity markings signify that when positive current enters both windings at the mar
